Device and installation features flush-mounted mixers

Almost all apartment owners are accustomed to the standard form mixer, when they see the tap itself and two or one valve. Even if these are extravagant models, they look much the same. The flush-mounted faucet does not have a long spout and levers in the visible part and looks quite unnoticeable, which allows you to use additional space at your discretion.

The familiar faucet brings out a mechanism that mixes water with different temperatures. In the hidden mixer it is impossible to find a mechanism that allows you to adjust the water manually.

A built-in faucet is so called due to the fact that its entire mechanism is mounted into the wall.

If we talk about the size of the invisible part of the mixer, then it is almost always equal to 11-15 cm in diameter and 9 cm in thickness. In order for such a structure to fit into the interstitial space, a distance of at least 9 cm is necessary. When repairing a bathroom with a large amount of space, no problems should arise.

There is a feeling that problems may arise if the house is of old construction with a miniature bathroom. But if during the planning it was calculated that the suspended plumbing would be installed in the room, then you can not worry - the indent in the classic version will be 10 cm from the intended wall. This is quite enough to build a hidden tap even in a small room.

You need to understand that one device only works for one mixer in the shower or in the bathroom. Also for each device it is necessary to connect two pipes with cold and hot water with a diameter of at least 15 mm.

Below are a number of features of flush-mounted mixers.

Support of the set temperature, without thermal differences. Mixers of all models are equipped with a thermostat. One of the problems of conventional spouts is the unpredictability of temperature: the mixer cannot independently supply water of the required temperature during the process of adjusting the tap. Built-in mixers easily solve such a problem, as the user himself sets the temperature, which does not change independently, but only after he changes it to another. If there is more than one spout in the apartment or in a separate room, then for each tap it is necessary to set its own temperature parameters.

Eliminates additional abrasions and bruises. Almost every inhabitant of the planet at least once crippled thanks to the bathroom items. With a hidden mixer, such incidents will not occur, since the projecting part of the device is too small. And you can now completely forget about a constantly tangling hose from a shower that tries to slip out of hand.

Aesthetics and convenience in one device. As already noted, with a concealed spout, there is no chance of hitting yourself or the child against the tap or getting tangled in the shower hose.

Control for a tap can be placed on one wall or even near a door, and the tap itself can be placed on another wall above the bath. With this model, you do not have to adapt to the pipes - the user will have complete freedom of creativity, because the mixer can be positioned wherever it pleases.

It harmoniously looks in the space of the room. In fact, the built-in faucet fits almost any bathroom interior. Suffice it to recall what the standard bathroom looks like: in virtually all interiors, all kinds of jars of soap, gel, shampoos, conditioners, and other items of daily toilet are visible. If you manage to hide all this in the cabinets, then the pipe with a watering cant just will not work out.

Save space and already in a small room. As mentioned above, the faucet takes up very little space in the visible part, so it can be considered a practical solution for a miniature bathroom.

In addition to this obvious advantage, it is possible to single out the fact that shelves for soap accessories can be attached to the place of an old mixer.However, in this case, you need to remember where the pipes go and stay away from this place with the working tools.

Rational approach to space planning in space. If the bathroom, in contrast to the previous item, is large, then the person can install two or more mixers on one device. For example, you can set two tropical souls opposite each other to create a hydrorelax. In this case, it is recommended to opt for larger diameter shower systems and make sure that the pump pipe connected to the mixers produces a sufficient amount of water. Otherwise, you can face intractable problems with water supply.

Simplifies cleaning. Most users are familiar with the situation when beautiful mixers after a while became a collection of divorces and plaque. To clean all the fittings in the bathroom, sometimes you have to spend the whole day off. With the built-in mixers, the cleaning time will be reduced several times, which saves time and manpower.

Mixers are divided by consumer character:

• For shower;
• for the bathroom;
• for washbasins;
• for bidet.

Also, cranes can be divided by place of installation:

• wall mounted copies;
• options installed on horizontal surfaces.

Classification by the type of mechanism that controls the flow and stream of water:

• mechanism type joystick;
• semi-turnaround mechanism;
• full turn mechanism.

By type of management:

• standard;
• sensory.

First of all, to install the faucet in the bathroom, it is necessary to drill a hole using a perforator. The crown in this case is required for concrete. In width, each hole should be approximately from 9.5 to 12 cm, and in diameter should reach 12-15 cm.

The second step is to drill the walls for the further installation of water pipes.

The final moment is the installation of the external elements themselves. Before embarking on this stage, it is necessary to make sure that the walls are completely repaired and the pipes are in working condition. Installing a flush-mounted faucet actually causes some difficulties,therefore, it is recommended to carefully read the instructions of the manufacturer of plumbing equipment. One of the main difficulties is the selection and installation of the mounting box.

Manufacturers are trying to most clearly depict the entire assembly process. Consistency also plays a huge role. But do not be afraid: if you take seriously and wisely to study the instructions, the installation process will take place very quickly and will not cause any trouble. There is a huge advantage in the fact that the user will install the device himself - he will know not only in theory but also in practice all the subtleties of installation and, in the event of a breakdown, he will be able to correct the situation without additional fuss and without unnecessary actions.

If you decide to install the equipment yourself, without resorting to the help of craftsmen, then it is worth remembering the precautionary measures. You must also be attentive to the work, especially in the case when the process of connecting valves with pipes begins. If there is a question in the choice of water pipes, then experts advise choosing copper or sewn polypropylene options.

“Try it on seven times, cut it once” - this proverb very accurately describes the hard work with water pipes. It is necessary to accurately and accurately arrange the pipes, carefully select all dimensions that are easy to calculate. It is also necessary to accurately calculate the height of the mixer and other devices.

To calculate the height at which the shower head is mounted, it is necessary to take the height of the tallest member of the family and add 40 centimeters to it (allowance for the height of the bathroom). You should also carefully check that the length of the washbasin faucet, taking into account the inclination of the water, coincides with the center of the washbasin itself.

Among the manufacturers of high-quality products can distinguish the company Kludi and Vitra. Their hygienic shower most often has three exits.

You should not save on the installation of plumbing equipment. It is necessary to bring a pipe to each device. The scheme should be clearly thought out and understandable. In case of problems with the spout, it will be much easier to disconnect one pipe from the water supply than several, and replace or repair it. Also, it will save from interruptions in water throughout the apartment.

For how to install a flush-mounted mixer, see the following video.