Unis primer: types and characteristics

High-quality primer - a necessary thing during the repair, because it is responsible for strengthening the adhesion between the wall and materials for decoration. If it is good not to prime the surface of the wall, then soon plaster will fall down from it, and the tile will go off together with glue. The Russian company Unis has long established itself as a manufacturer of high-quality dry building mixtures, as well as a variety of primer compositions that contribute to the uniform application of finishing materials both inside and outside the premises.

Thanks to Unis, construction work will be carried out much faster, since these substances are designed to dry in the minimum amount of time. Also the use of this mixture helps to reduce the consumption of expensive construction adhesives, paint, any plaster and various means for treating the floor.Another advantage of deep penetration is that they plug holes and cracks in any kind of surfaces well.

One such bucket is enough to fully cover the surface of 31 m2 with one layer. From this it follows that one square meter will need up to 0.35 liters of material, which is quite economical. The outer surface, primed in one layer, dries out in about three hours at a humidity of up to 60% and a temperature of 19 degrees. It should be borne in mind that the use of mixtures on the external walls of buildings is strictly prohibited at temperatures below +5 and above +30 degrees and air humidity more than 75%. If the work is carried out inside a heated room, then they can be made at any time, regardless of humidity and temperature.

The company produces four types of soil mixtures, each of which fits a certain type of base and has its own characteristics:

• primer for interior work;
• universal ground;
• deep penetration primer;
• concrete asset

Capacities in 10 l from strong plastic of bright yellow color can be easily seen on the shelf of any hardware store. The cost of each composition varies from 200-400 rubles, which is quite economical, especially in comparison with imported goods of a similar composition. Consider each of the mixtures separately and learn about the individual characteristics of each.

As the name implies, this mixture is designed to process the internal surfaces of the room. It perfectly aligns the area of ​​application, removes dust and increases adhesion between the surface and the future finish. This composition strengthens the walls and the floor, as well as prepares them for the next step in applying decorative tools and finishes, which include putty, plaster, tile glue, and the tiles or wallpapers themselves.

This type is designed to prepare and strengthen the area of ​​durable brick, concrete, plaster, limestone, plasterboard materials and gypsum boards. The main property of this mixture is clear from the name - it penetrates deep enough into the base of the surface, perfectly sealing and strengthening old, uneven, liquid-absorbing materials. Also primer promotes uniform distribution of the absorbed liquid.

This type of soil mixture provides greater strength of the applied materials and their resistance to cracks, as well as, like any other, increases the strength of adhesion of agents with the treatment area. The use of Unis saves consumption of subsequent repair products and guarantees the safety of the original appearance of the foundation.

This type of soil product is designed for the preparation, strengthening and dedusting of surfaces before the next step in the application of finishing mixtures and decorative coatings.In case you doubt the choice of one or another means, you can safely take this universal product, because it is applicable to the exterior of buildings, and for closed premises, regardless of the level of moisture and temperature.

The main feature of this composition is to ensure the increase in strength of subsequent materials., as well as the strength of the coupling between them and the wall. Such a variety perfectly reduces the water absorbency of the treated surface and levels it. It is responsible for maintaining the high quality of the treated area for a long time and extends the service of other means. Like other types of soil, this composition helps to save on the amount of future finishing or decorative materials. The product dries very quickly, leaving no stickiness, which reduces repair time.

This kind of soil mixtures created for smooth and poorly liquid-absorbing areas. This product is perfect for any bases of concrete, foam concrete and gas silicate before applying plaster or tile adhesive. It can be used both for the priming of external walls and for the treatment of internal surfaces in rooms.

Before you start using Unis primers, you should carefully study and prepare the application area that will be processed. It must be dry and have bearing properties. Before direct coating, all separating parts, excess coatings must be removed, cleaned from stains and other contaminants that can prevent a strong adhesion of the soil product to the surface.

When all of the above actions are completed, you need to take any tool for painting surfaces: it can be a roller, and a construction brush, and a spray gun and a brush. The mixture should be gently and evenly applied to the surface, preventing the formation of puddles. Before taking the next steps, you need to wait until the treated area is completely dry.

A large number of positive feedback from ordinary users indicates that Unis products are really very good and easy to use. Many point to the excellent composition of soil mixtures, which is similar to foreign analogues. Of course, despite the similar composition, Unis is inferior in quality to its import rivals, but at the same time the price is quite democratic, which is also noted by the majority of users.

How to align walls using materials from UNIS, see the following video.